How do I connect to a terminal to a serial-to-USB

Question

I am trying to connect minicom to a serial device that is connected via a USB-to-serial adapter. This is a PL2303 and from everything I've read no additional drivers are required. The device is recognised as a PL2303.

I'm a beginner at minicom. Is this the correct command to execute? Or do I need to configure something?

$ sudo minicom --device /dev/ttyUSB0
minicom: cannot open /dev/ttyUSB0: No such file or directory

$ sudo lsusb -v

Bus 002 Device 006: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Device Descriptor:
  bLength                18
  bDescriptorType         1

$ tail /var/log/syslog  #then removed and attached the device.
Mar 13 23:31:49 ubuntu kernel: [807996.786805] usb 2-1: pl2303 converter now attached to ttyUSB0
Mar 13 23:34:44 ubuntu kernel: [808172.155129] usb 2-1: USB disconnect, address 7
Mar 13 23:34:44 ubuntu kernel: [808172.156321] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
Mar 13 23:34:44 ubuntu kernel: [808172.156374] pl2303 2-1:1.0: device disconnected
Mar 13 23:34:52 ubuntu kernel: [808179.497856] usb 2-1: new full speed USB device using uhci_hcd and address 8
Mar 13 23:34:52 ubuntu kernel: [808179.785845] pl2303 2-1:1.0: pl2303 converter detected
Mar 13 23:34:52 ubuntu kernel: [808179.872309] usb 2-1: pl2303 converter now attached to ttyUSB0

Answer 1

I get get the same minicom error, "cannot open /dev/ttyUSB0: No such file or directory"

Three notes:

1. I get the error when the device attached to the serial port end of my Prolific Technology PL2303 USB/Serial adapter is turned off. After turning on the device (an embedded controller running Linux) minicom connected fine.

2. I have to run as super user (i.e. sudo minicom)

3. Sometimes I have to unplug and plug back in the USB-to-serial adapter to get minicom to connect to it.

I am running Ubuntu 10.04 LTS (Lucid Lynx) under VMware (running on Windows 7). In this situation, make sure the device is attached to VM operating system by right clicking on the USB/Serial USB icon in the lower right of the VMware window and select Connect (Disconnect from Host).

Remember to press Ctrl + A to get minicom's prompt, and type X to exit the program. Just exiting the terminal session running minicom will leave the process running.

Answer 2

You will need to set the permissions every time you plug the converter in. I use PuTTY to connect. In order to do so, I have created a little Bash script to sort out the permissions and launch PuTTY:

#!/bin/bash
sudo chmod 666 /dev/ttyUSB0

putty

P.S. I would never recommend that permissions are set to 777.

Answer 3

I suggest that newbies connect a PL2303 to Ubuntu, chmod 777 /dev/ttyUSB0 (file-permissions) and connect to a CuteCom serial terminal. The CuteCom UI is simple \ intuitive. If the PL2303 is continuously broadcasting data, then Cutecom will display data in hex format

Answer 4

I just got my GUC232A cable with a molded-in PL2302 converter chip.

In addition to adding myself and br to group dialout, I found this helpful tip in the README.Debian file in /usr/share/doc/bottlerocket:

This package uses debconf to configure the /dev/firecracker symlink, should you need to change the symlink in the future run this command:

dpkg-reconfigure -pmedium bottlerocket

That will then prompt you for your new serial port and modify the symlink. This is required for proper use of bottlerocket.

I did that and voila! bottlerocket is able to communicate with my X-10 devices.