Target non specific version of an assembly

问题:

I m trying to not target a specific version of a dll but I m not quite sure how. I have set the option Specific Version on the properties of the assembly to false, however if i try to run the application and the version of the requested assembly is a previous one, I get a:

FileLoadException: Could not load file or assembly 

This is happening when the version of the referenced dll does not exactly match the current one. I would believe that the issue is on how to reference this assembly.

回答1:

In general, if you are trying to use a specific version of an assembly the below doesn't really apply, you should just use the version you need.

However, sometimes you can run into a situation where you have this:

AssemblyX - references version 1.2.1 of AssemblyZ
AssemblyY - references version 1.2.2 of AssemblyZ

But your project needs both AssemblyX and AssemblyY.

So how do you resolve this? You can either put 1.2.1 and 1.2.2 of AssemblyZ in the GAC, or, if you're sure there aren't any compatibility issues, you can use assembly rebinding. Here's an example (this goes in your Web.config or App.config file):

<configuration>
   <runtime>
      <assemblyBinding xmlns="urn:schemas-microsoft-com:asm.v1">
         <dependentAssembly>
            <assemblyIdentity name="myAssembly"
                              publicKeyToken="32ab4ba45e0a69a1"
                              culture="neutral" />
            <bindingRedirect oldVersion="1.0.0.0"
                             newVersion="2.0.0.0"/>
         </dependentAssembly>
      </assemblyBinding>
   </runtime>
</configuration>

What this basically says is that if any assemblies in your solution reference 1.0.0.0 of myAssembly, then they should really use version 2.0.0.0. And you're expected to have version 2.0.0.0 present in the path.

A hack you can use when you always want them to use a specific version of the assembly is to specify a version range, like this:

        <dependentAssembly>
            <assemblyIdentity name="MyAssembly" publicKeyToken="B7567367622062C6" culture="neutral" />
            <bindingRedirect oldVersion="0.0.0.0-3.0.0.0" newVersion="1.2.1.0" />
        </dependentAssembly>

This will force version 1.2.1.0 of MyAssembly to be used for any version reference of MyAssembly between 0.0.0.0 and 3.0.0.0.

回答2:

the only ways around this issue I found so far are:

1) ILMerge the dll with the dependency I have 2) provide the the dependency (in this case a dll) 3) not signong the assembly , tho this would be quite hard, cause i ll need to "unsign" the hierachy

回答3:

You can have both dlls and can use bindingRedirect as in below link

dll versioning in dotnet

<configuration>
   <runtime>
      <assemblyBinding xmlns="urn:schemas-microsoft-com:asm.v1">
         <dependentAssembly>
            <assemblyIdentity name="AssemblyName"
                              publicKeyToken="32ab4ba45e0a69a1"
                              culture="neutral" />
            <bindingRedirect oldVersion="1.0.0.0"
                             newVersion="2.0.0.0"/>
         </dependentAssembly>
      </assemblyBinding>
   </runtime>
</configuration>

回答4:

While the code example for App.Config below is correct you might wish to keep GAC policy from overriding your desire by adding the following publisherPolicy apply="no" in either the assemblyBinding tree which will cause all assemblys to ignore the GAC publisher policy or you may place the publisherPolicy apply="no" /> in the dependentAssembly tree and this will by pass publisherPolicy for that assembly only.

   { <configuration>
   <runtime>
      <assemblyBinding xmlns="urn:schemas-microsoft-com:asm.v1">
        <publisherPolicy apply="no" /> // This applies to the whole application - all references
         <dependentAssembly>
         <publisherPolicy apply="no" /> // This applies only to this assembly
            <assemblyIdentity name="AssemblyName"
                              publicKeyToken="32ab4ba45e0a69a1"
                              culture="neutral" />
            <bindingRedirect oldVersion="1.0.0.0"
                             newVersion="2.0.0.0"/>
         </dependentAssembly>
      </assemblyBinding>}

For more info see: MSDN reference