SSE instruction MOVSD (extended: floating point sc

I am somehow confused by the MOVSD assembly instruction. I wrote some numerical code computing some matrix multiplication, simply using ordinary C code with no SSE intrinsics. I do not even include the header file for SSE2 intrinsics for compilation. But when I check the assembler output, I see that:

1) 128-bit vector registers XMM are used; 2) SSE2 instruction MOVSD is invoked.

I understand that MOVSD essentially operates on single double precision floating point. It only uses the lower 64-bit of an XMM register and set the upper 64-bit 0. But I just don't understand two things:

1) I never give the compiler any hint for using SSE2. Plus, I am using GCC not intel compiler. As far as I know, intel compiler will automatically seek opportunities for vectorization, but GCC will not. So how does GCC know to use MOVSD?? Or, has this x86 instruction been around long before SSE instruction set, and the _mm_load_sd() intrinsics in SSE2 is just to provide backward compatibility for using XMM registers for scalar computation?

2) Why does not the compiler use other floating point registers, either the 80-bit floating point stack, or 64-bit floating point registers?? Why must it take the toll using XMM register (by setting upper 64-bit 0 and essentially wasting that storage)? Does XMM do provide faster access??

By the way, I have another question regarding SSE2. I just can't see the difference between _mm_store_sd() and _mm_storel_sd(). Both store the lower 64-bit value to an address. What is the difference? Performance difference?? Alignment difference??

Thank you.

Update 1:

OKAY, obviously when I first asked this question, I lacked some basic knowledge on how a CPU manages floating point operations. So experts tend to think my question is non-sense. Since I did not include even the shortest sample C code, people might think this question vague as well. Here I would provide a review as an answer, which hopefully will be useful to any people unclear about the floating point operations on modern CPUs.

A review of floating point scalar/vector processing on modern CPUs

The idea of vector processing dates back to old time vector processors, but these processors had been superseded by modern architectures with cache systems. So we focus on modern CPUs, especially x86 and x86-64. These architectures are the main stream in high performance scientific computing.

Since i386, Intel introduced the floating point stack where floating point numbers up to 80-bit wide can be held. This stack is commonly known as x87 or 387 floating point "registers", with a set of x87 FPU instructions. x87 stack are not real, directly addressable registers like general purpose registers, as they are on a stack. Access to register st(i) is by offsetting the stack top register %st(0) or simply %st. With help of an instruction FXCH which swaps the contents between current stack top %st and some offset register %st(i), random access can be achieved. But FXCH can impose some performance penalty, though minimized. x87 stack provides high precision computation by calculating intermediate results with 80 bits of precision by default, to minimise roundoff error in numerically unstable algorithms. However, x87 instructions are completely scalar.

The first effort on vectorization is the MMX instruction set, which implemented integer vector operations. The vector registers under MMX are 64-bit wide registers MMX0, MMX1, ..., MMX7. Each can be used to hold either 64-bit integers, or multiple smaller integers in a "packed" format. A single instruction can then be applied to two 32-bit integers, four 16-bit integers, or eight 8-bit integers at once. So now there are the legacy general purpose registers for scalar integer operations, as well as new MMX for integer vector operations with no shared execution resources. But MMX shared execution resources with scalar x87 FPU operation: each MMX register corresponded to the lower 64 bits of an x87 register, and the upper 16 bits of the x87 registers is unused. These MMX registers were each directly addressable. But the aliasing made it difficult to work with floating point and integer vector operations in the same application. To maximize performance, programmers often used the processor exclusively in one mode or the other, deferring the relatively slow switch between them as long as possible.

Later, SSE created a separate set of 128-bit wide registers XMM0–XMM7 along side of x87 stack. SSE instructions focused exclusively on single-precision floating-point operations (32-bit); integer vector operations were still performed using the MMX register and MMX instruction set. But now both operations can proceed at the same time, as they share no execution resources. It is important to know that SSE not only do floating point vector operations, but also floating point scalar operations. Essentially it provides a new place where floating operations take place, and the x87 stack is no longer prior choice to carry out floating operations. Using XMM registers for scalar floating point operations is faster than using x87 stack, as all XMM registers are easier to access, while the x87 stack can't be randomly accessed without FXCH. When I posted my question, I was clearly unaware of this fact. The other concept I was not clear about is that general purpose registers are integer/address registers. Even if they are 64-bit on x86-64, they can not hold 64-bit floating point. The main reason is that the execution unit associated with general purpose registers is ALU (arithmetic & logical unit), which is not for floating point computation.

SSE2 is a major progress, as it extends vector data type, so SSE2 instructions, either scalar or vector, can work with all C standard data type. Such extension in fact makes MMX obsolete. Also, x87 stack is no long as important as it once was. Since there are two alternative places where floating point operations can take place, you can specify your option to the compiler. For example for GCC, compilation with flag

-mfpmath=387

will schedule floating point operations on the legacy x87 stack. Note that this seems to be the default for 32-bit x86, even if SSE is already available. For example, I have an Intel Core2Duo laptop made in 2007, and it was already equipped with SSE release up to version SSE4, while GCC will still by default use x87 stack, which makes scientific computations unnecessarily slower. In this case, we need compile with flag

-mfpmath=sse

and GCC will schedule floating point operations on XMM registers. 64-bit x86-64 user needs not worry about such configuration as this is default on x86-64. Such signal will only affect scalar floating point operation. If we have written code using vector instructions and compiler the code with flag

-msse2

then XMM registers will be the only place where computation can take place. In other words, this flags turns on -mfpmath=sse. For more information see GCC's configuration of x86, x86-64. For examples of writing SSE2 C code, see my other post How to ask GCC to completely unroll this loop (i.e., peel this loop)?.

SSE set of instructions, though very useful, are not the latest vector extensions. The AVX, advanced vector extensions enhances SSE by providing 3-operands and 4 operands instructions. See number of operands in instruction set if you are unclear of what this means. 3-operands instruction optimizes the commonly seen fused multiply-add (FMA) operation in scientific computing by 1) using 1 fewer register; 2) reducing the explicit amount of data movement between registers; 3) speeding up FMA computations in itself. For example of using AVX, see @Nominal Animal's answer to my post.