MySQL ON vs USING?

问题:

In a MySQL JOIN, what is the difference between ON and USING()? As far as I can tell, USING() is just more convenient syntax, whereas ON allows a little more flexibility when the column names are not identical. However, that difference is so minor, you'd think they'd just do away with USING().

Is there more to this than meets the eye? If yes, which should I use in a given situation?

回答1:

It is mostly syntactic sugar, but a couple differences are noteworthy:

ON is the more general of the two. One can join tables ON a column, a set of columns and even a condition. For example:

SELECT * FROM world.City JOIN world.Country ON (City.CountryCode = Country.Code) WHERE ...

USING is useful when both tables share a column of the exact same name on which they join. In this case, one may say:

SELECT ... FROM film JOIN film_actor USING (film_id) WHERE ...

An additional nice treat is that one does not need to fully qualify the joining columns:

SELECT film.title, film_id -- film_id is not prefixed
FROM film
JOIN film_actor USING (film_id)
WHERE ...

To illustrate, to do the above with ON, we would have to write:

SELECT film.title, film.film_id -- film.film_id is required here
FROM film
JOIN film_actor ON (film.film_id = film_actor.film_id)
WHERE ...

Notice the film.film_id qualification in the SELECT clause. It would be invalid to just say film_id since that would make for an ambiguity:

ERROR 1052 (23000): Column 'film_id' in field list is ambiguous

As for select *, the joining column appears in the result set twice with ON while it appears only once with USING:

mysql> create table t(i int);insert t select 1;create table t2 select*from t;
Query OK, 0 rows affected (0.11 sec)

Query OK, 1 row affected (0.00 sec)
Records: 1  Duplicates: 0  Warnings: 0

Query OK, 1 row affected (0.19 sec)
Records: 1  Duplicates: 0  Warnings: 0

mysql> select*from t join t2 on t.i=t2.i;
+------+------+
| i    | i    |
+------+------+
|    1 |    1 |
+------+------+
1 row in set (0.00 sec)

mysql> select*from t join t2 using(i);
+------+
| i    |
+------+
|    1 |
+------+
1 row in set (0.00 sec)

mysql>

回答2:

Thought I would chip in here with when I have found ON to be more useful than USING. It is when OUTER joins are introduced into queries.

ON benefits from allowing the results set of the table that a query is OUTER joining onto to be restricted while maintaining the OUTER join. Attempting to restrict the results set through specifying a WHERE clause will, effectively, change the OUTER join into an INNER join.

Granted this may be a relative corner case. Worth putting out there though.....

For example:

CREATE TABLE country (
   countryId int(10) unsigned NOT NULL PRIMARY KEY AUTO_INCREMENT,
   country varchar(50) not null,
  UNIQUE KEY countryUIdx1 (country)
) ENGINE=InnoDB;

insert into country(country) values ("France");
insert into country(country) values ("China");
insert into country(country) values ("USA");
insert into country(country) values ("Italy");
insert into country(country) values ("UK");
insert into country(country) values ("Monaco");


CREATE TABLE city (
  cityId int(10) unsigned NOT NULL PRIMARY KEY AUTO_INCREMENT,
  countryId int(10) unsigned not null,
  city varchar(50) not null,
  hasAirport boolean not null default true,
  UNIQUE KEY cityUIdx1 (countryId,city),
  CONSTRAINT city_country_fk1 FOREIGN KEY (countryId) REFERENCES country (countryId)
) ENGINE=InnoDB;


insert into city (countryId,city,hasAirport) values (1,"Paris",true);
insert into city (countryId,city,hasAirport) values (2,"Bejing",true);
insert into city (countryId,city,hasAirport) values (3,"New York",true);
insert into city (countryId,city,hasAirport) values (4,"Napoli",true);
insert into city (countryId,city,hasAirport) values (5,"Manchester",true);
insert into city (countryId,city,hasAirport) values (5,"Birmingham",false);
insert into city (countryId,city,hasAirport) values (3,"Cincinatti",false);
insert into city (countryId,city,hasAirport) values (6,"Monaco",false);

-- Gah. Left outer join is now effectively an inner join 
-- because of the where predicate
select *
from country left join city using (countryId)
where hasAirport
; 

-- Hooray! I can see Monaco again thanks to 
-- moving my predicate into the ON
select *
from country co left join city ci on (co.countryId=ci.countryId and ci.hasAirport)
; 

回答3:

Wikipedia has the following information about USING:

The USING construct is more than mere syntactic sugar, however, since the result set differs from the result set of the version with the explicit predicate. Specifically, any columns mentioned in the USING list will appear only once, with an unqualified name, rather than once for each table in the join. In the case above, there will be a single DepartmentID column and no employee.DepartmentID or department.DepartmentID.

Tables that it was talking about:

The Postgres documentation also defines them pretty well:

The ON clause is the most general kind of join condition: it takes a Boolean value expression of the same kind as is used in a WHERE clause. A pair of rows from T1 and T2 match if the ON expression evaluates to true.

The USING clause is a shorthand that allows you to take advantage of the specific situation where both sides of the join use the same name for the joining column(s). It takes a comma-separated list of the shared column names and forms a join condition that includes an equality comparison for each one. For example, joining T1 and T2 with USING (a, b) produces the join condition ON T1.a = T2.a AND T1.b = T2.b.

Furthermore, the output of JOIN USING suppresses redundant columns: there is no need to print both of the matched columns, since they must have equal values. While JOIN ON produces all columns from T1 followed by all columns from T2, JOIN USING produces one output column for each of the listed column pairs (in the listed order), followed by any remaining columns from T1, followed by any remaining columns from T2.

回答4:

For those experimenting with this in phpMyAdmin, just a word:

phpMyAdmin appears to have a few problems with USING. For the record this is phpMyAdmin run on Linux Mint, version: "4.5.4.1deb2ubuntu2", Database server: "10.2.14-MariaDB-10.2.14+maria~xenial - mariadb.org binary distribution".

I have run SELECT commands using JOIN and USING in both phpMyAdmin and in Terminal (command line), and the ones in phpMyAdmin produce some baffling responses:

1) a LIMIT clause at the end appears to be ignored.
2) the supposed number of rows as reported at the top of the page with the results is sometimes wrong: for example 4 are returned, but at the top it says "Showing rows 0 - 24 (2503 total, Query took 0.0018 seconds.)"

Logging on to mysql normally and running the same queries does not produce these errors. Nor do these errors occur when running the same query in phpMyAdmin using JOIN ... ON .... Presumably a phpMyAdmin bug.