What is CMake equivalent of 'configure --prefi

问题:

I do cmake . && make all install. This works, but installs to /usr/local.

I need to install to a different prefix (for example, to /usr).

What is the cmake and make command line to install to /usr instead of /usr/local?

回答1:

You can pass in any CMake variable on the command line, or edit cached variables using ccmake/cmake-gui. On the command line,

cmake -DCMAKE_INSTALL_PREFIX:PATH=/usr . && make all install

Would configure the project, build all targets and install to the /usr prefix. The type (PATH) is not strictly necessary, but would cause the Qt based cmake-gui to present the directory chooser dialog.

Some minor additions as comments make it clear that providing a simple equivalence is not enough for some. Best practice would be to use an external build directory, i.e. not the source directly. Also to use more generic CMake syntax abstracting the generator.

mkdir build && cd build && cmake -DCMAKE_INSTALL_PREFIX:PATH=/usr .. && cmake --build . --target install --config Release

You can see it gets quite a bit longer, and isn't directly equivalent anymore, but is closer to best practices in a fairly concise form... The --config is only used by multi-configuration generators (i.e. MSVC), ignored by others.

回答2:

The ":PATH" part in the accepted answer can be omitted. This syntax may be more memorable:

cmake -DCMAKE_INSTALL_PREFIX=/usr . && make all install

...as used in the answers here.

回答3:

Note that in both CMake and Autotools you don't always have to set the installation path at configure time. You can use DESTDIR at install time (see also here) instead as in:

make DESTDIR=<installhere> install

See also this question which explains the subtle difference between DESTDIR and PREFIX.

This is intended for staged installs and to allow for storing programs in a different location from where they are run e.g. /etc/alternatives via symbolic links.

However, if your package is relocatable and doesn't need any hard coded (prefix) paths set via the configure stage you may be able to skip it. So instead of:

cmake -DCMAKE_INSTALL_PREFIX=/usr . && make all install

you would run:

cmake . && make DESTDIR=/usr all install

Note that, as user7498341 points out, this is not appropriate for cases where you really should be using PREFIX.

回答4:

The way I build CMake projects cross platform is the following:

/project-root> mkdir build
/project-root> cd build
/project-root/build> cmake -G "<generator>" -DCMAKE_INSTALL_PREFIX=stage ..
/project-root/build> cmake --build . --target=install --config=Release

• The first two lines create the out-of-source build directory
• The third line generates the build system specifying where to put the installation result (which I always place in ./project-root/build/stage - the path is always considered relative to the current directory if it is not absolute)
• The fourth line builds the project configured in . with the buildsystem configured in the line before. It will execute the install target which also builds all necessary dependent targets if they need to be built and then copies the files into the CMAKE_INSTALL_PREFIX (which in this case is ./project-root/build/stage. For multi-configuration builds, like in Visual Studio, you can also specify the configuration with the optional --config <config> flag.
• The good part when using the cmake --build command is that it works for all generators (i.e. makefiles and Visual Studio) without needing different commands.

Afterwards I use the installed files to create packages or include them in other projects...

回答5:

Regarding Bruce Adams answer:

Your answer creates dangerous confusion. DESTDIR is intended for installs out of the root tree. It allows one to see what would be installed in the root tree if one did not specify DESTDIR. PREFIX is the base directory upon which the real installation is based.

For example, PREFIX=/usr/local indicates that the final destination of a package is /usr/local. Using DESTDIR=$HOME will install the files as if $HOME was the root (/). If, say DESTDIR, was /tmp/destdir, one could see what 'make install' would affect. In that spirit, DESTDIR should never affect the built objects.

A makefile segment to explain it:

install:
    cp program $DESTDIR$PREFIX/bin/program

Programs must assume that PREFIX is the base directory of the final (i.e. production) directory. The possibility of symlinking a program installed in DESTDIR=/something only means that the program does not access files based upon PREFIX as it would simply not work. cat(1) is a program that (in its simplest form) can run from anywhere. Here is an example that won't:

prog.pseudo.in:
    open("@prefix@/share/prog.db")
    ...

prog:
    sed -e "s/@prefix@/$PREFIX/" prog.pseudo.in > prog.pseudo
    compile prog.pseudo

install:
    cp prog $DESTDIR$PREFIX/bin/prog
    cp prog.db $DESTDIR$PREFIX/share/prog.db

If you tried to run prog from elsewhere than $PREFIX/bin/prog, prog.db would never be found as it is not in its expected location.

Finally, /etc/alternatives really does not work this way. There are symlinks to programs installed in the root tree (e.g. vi -> /usr/bin/nvi, vi -> /usr/bin/vim, etc.).

回答6:

It is considered bad practice to invoke the actual generator (e.g. via make) if using CMake. It is highly recommended to do it like this:

1. Configure phase:

   cmake -Hfoo -B_builds/foo/debug -G"Unix Makefiles" -DCMAKE_BUILD_TYPE=Debug -DCMAKE_DEBUG_POSTFIX=d -DCMAKE_INSTALL_PREFIX=/usr
   

2. Build and Install phases

   cmake --build _builds/foo/debug --config Debug --target install
   

When following this approach, the generator can be easily switched (e.g. -GNinja for Ninja) without having to remember any generator-specific commands.